your location: 首页>>News>>company news

Service Hotline

+86760-8787 8587

Non-standard electroplating carriage bolts Square bolts Round head screws Mushroom head bolts

author:[email protected] Click:3744end source: time:2022-11-17 05:54:25

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: one-piece expansion b...

At present, when fastening parts on thin-walled products or thin plates in our country, screws are usually used to fasten, and welding nuts are required to make the thin plate easy to burn through, or the objects are drilled and tapped to connect, so that the product is deformed and the connection strength is not strong. , It cannot be fastened on some equipment, the operation is inconvenient, and the production efficiency is low.

Subway tunnels can be divided into rectangular, arched, circular, and elliptical end face forms according to the section shape of the section tunnel. The rectangular end face can be divided into single-span, double-span and multi-span types. There are two types of circles. The subway tunnel needs to install electromechanical equipment through bolts, insert T-shaped bolts into the preset holes on the shield plate of the subway tunnel, and then cast and fix it. The bolts are smooth and the contact surface is small. The bolts installed in the shield plate are easy to fall off, causing the installed equipment to fall and damage or causing losses to pedestrians or vehicles passing in the tunnel. Therefore, it is necessary to further improve the current bolts.

Washers (spring) washers, circlips are elastic pads or card lock washers a washer that prevents bolts from loosening. The working principle of lock washers is very simple. It consists of two washers. The outside is a radial relief surface, and the inside is a helical tooth surface. When assembling, the inner helical tooth surfaces are opposite each other, and the outer radial raised surface is engaged with the contact surfaces at both ends. When the connecting piece is vibrated and the bolt tends to loosen, only the inner helical tooth surfaces of the two washers are allowed to face each other. Staggered movement, resulting in lifting tension, so as to achieve 100% locking.

The inch thread is the thread size marked in inch. According to the shape, it is divided into two types: cylindrical and conical; according to the tooth angle, it is divided into two types: 55° and 60°. The 1/4, 1/2, 1/8 marks in the thread refer to the diameter of the thread size in inches. One inch equals 8 cents, 1/4 inch equals 2 cents, and so on.

The positioning pin is a pin designed to accurately position the two adjacent parts of the mold in a mold composed of two or more parts. It can be seen that the positioning pin plays a positioning role, and the mold must be accurately synchronized when it is closed. product, and the positioning pin can make the upper and lower molds play a role in accurate positioning. In the mold design and manufacture of Yueluo, the positioning pin is one of the most common parts. Since it is only used for positioning between parts, few people will pay too much attention to it. In the cold stamping process of Yueluo, the dimensional accuracy of the blanking parts depends on the size of the working part of the punch and the concave die, and the dimensional difference between them constitutes the blanking die gap. Gap is an important process parameter for die design, and its size has a great influence on the quality of the section of the blanking part, the blanking force, and the life of the die. If the gap is too large, punching burrs will appear in punching; if the gap is too small, secondary cracks will occur in the section and extrusion burrs will appear, which will make the quality of the section after punching unsatisfactory, and a reasonable gap will not only help the punching section. The improvement of quality also contributes to the improvement of the lifespan of the 9 bottles.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: flat round head bolts, half tooth furniture screws, spring pins, percussion flat cap rivets made of copper rivets and other products, we can provide you with The right fastener solution for you.

Non-standard electroplating

carriage bolt


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].