your location: 首页>>News>>company news

Service Hotline

+86760-8787 8587

Customized aluminum screws non-standard special-shaped flat head hand screw aluminum screws 3/4 5/8

author:[email protected] Click:3622end source: time:2022-10-02 20:54:33

Summary of information:We have more than ten years of experience in the production of screw industry, the main products are: aluminum alloy nut...

1. The twisted screw should be considered according to the actual inner diameter of the barrel, and the outer diameter deviation of the new screw should be given according to the normal clearance with the barrel. 2. After the thread surface with the reduced diameter of the worn screw is treated, the wear-resistant tungsten carbide alloy is thermally sprayed, and then ground to size. 3. Surfacing wear-resistant tungsten carbide alloy on the thread part of the worn screw. According to the degree of screw wear, surfacing welding is 1~2mm thick, and then the screw is ground and processed to size. This wear-resistant tungsten carbide alloy is composed of materials such as C, Cr, Vi, Co, W and B, which increases the wear resistance and corrosion resistance of the screw. 4. The bottom diameter of the screw is repaired by electroplating hard chromium. Chromium is also a wear-resistant and corrosion-resistant metal, but the hard chromium layer is easier to fall off.

Material broadcast Cross recessed screws are made of iron and stainless steel. Iron cross recessed screws are also called carbon steel screws. Stainless steel cross recessed screws include stainless steel SUS201 and stainless steel SUS304, and stainless steel SUS316 cross recessed screws.

A screw belt structure, especially a screw belt that can position the screws on the screw belt, so that the screws do not swing, so that the screws can be stably aligned with the points where the screws are to be screwed, and the screw fixation of the screws is facilitated. In its overall implementation and use, the innovative design of the screw belt structure increases the practical function characteristics.

The process of removing iron oxide plate from cold heading steel wire rod is stripping and dephosphorization. There are two methods: mechanical dephosphorization and chemical pickling. Replacing the chemical pickling process of wire rod with mechanical phosphorus removal not only improves productivity, but also reduces environmental pollution. This phosphorus removal process includes bending method (the round wheel with triangular grooves is commonly used to repeatedly bend the wire rod), spray nine method, etc. The phosphorus removal effect is good, but the residual iron and phosphorus cannot be removed (the removal rate of iron oxide scale is 97%) ), especially when the iron oxide scale is very sticky, therefore, mechanical phosphorus removal is affected by iron scale thickness, structure and stress state. Carbon steel wire rods used for low strength fasteners (less than or equal to 6.8) High-strength bolts (greater than or equal to grade 8.8) use wire rods to remove all iron oxide scales after mechanical dephosphorization, and then go through a chemical pickling process for compound dephosphorization. For low carbon steel wire rods, the iron sheets left by mechanical dephosphorization are likely to cause uneven wear of grain draft. When the grain draft hole adheres to the iron sheet when the wire rod rubs against the external temperature, the surface of the wire rod produces longitudinal grain marks. More than 95% are caused by scratches on the surface of the steel wire during the drawing process. Therefore, the mechanical phosphorus removal method is not suitable for high-speed drawing.

Guangdong Yueluo Hardware Industry Co., Ltd. has a simple structure, low processing difficulty, and convenient riveting. The whole pin has the same diameter except for the annular groove. The drawn wire can be directly used, which saves the cost of materials and machining costs, and improves the production speed and efficiency. The structure does not require high machining accuracy of the hole, which can effectively reduce the machining cost and the rework rate of the parts.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: extended screw nut bolts, anti-seismic tightening screws, nut pads, stainless steel screws for riding tube clamps and other products, we can provide you with suitable products for you. Fastener Solutions.

Non-standard shaped

Customized aluminum screws


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].