your location: 首页>>News>>company news

Service Hotline

+86760-8787 8587

Customized rivet nut flat head knurled rivet nut electric control cabinet screw nut 5/8

author:[email protected] Click:4503end source: time:2022-09-27 21:27:10

Summary of information:We have more than ten years of experience in screw industry production, the main products are: 304 countersunk head scre...

Guangdong Yueluo Hardware Industry Co., Ltd. has upgraded and combined the fastening nut and the hexagonal nut to ensure the original function of the nut. The nut can be easily and safely disassembled by preparing practical small parts. The inner diameter of the lock ring is 0.1mm larger than that of the hexagonal nut, which is convenient for installation.

The above riveting requires special tools and equipment, which cannot be used in actual specific occasions. In the case of no electricity and no air, only manual tools can be used; and manual tools cannot be used for large types of rivets due to limited human strength. Moreover, after the rivet is disassembled, the rivet itself will be destroyed and cannot be reused.

The purpose of Yueluo is to provide a stamping process for screws. Before stamping, a sticky protective layer is coated on the pressure surface of the screw blank. The sticky protective layer can play a buffering role during stamping and prevent the screw head from being damaged. In order to achieve the above purpose, the technical solution of Yueluo is to design a screw stamping process, which uses a stamping die to stamp the screw blank and punch out the screw head; and before stamping, the pressure surface of the screw blank is coated with adhesive protection. layer.

Generally, we have to divide the fine thread nut and the coarse thread nut first, but in fact, no matter what kind of fine thread, coarse thread, their specifications are the same, their specifications are M3, M4, M5, M6, M8, M10, etc. . But there is another kind of hexagonal nut, which is divided into English and American, which is only a different national standard. Made in China, it is called the national standard hexagon nut

1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: blind hole riveting nuts, car repair gecko screws, round cup screws with pads, round head stainless steel round knurled hand nuts and other products, We can provide you with the right fastener solution for you.

Flat knurled rivet nuts

Customized rivet nuts


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].