Service HotlineMetric threads are measured in MM (millimeters) and have a cusp angle of 60 degrees. Both US and Imperial threads are measured in inches. The cusp angle of the American thread is also 60 degrees, while the cusp angle of the imperial thread is 55 degrees. Due to the different units of measurement, the representation methods of various threads are also different. For example, M16-2X60 represents a metric thread. His specific meaning is that the nominal diameter of the screw is 16MM, the pitch is 2MM, and the length is 60MM. Another example: 1/4—20X3/4 means the inch thread, what he specifically means is the nominal diameter of the screw It is 1/4 inch (one inch = 25.4MM), there are 20 teeth on one inch, and the length is 3/4 inch. In addition, if you want to express American screws, UNC and UNF are usually added to the back of the British screws to distinguish between American coarse teeth or American fine teeth. In the usual domestic sales business, the most common standards we encounter are GB (National Standard) and DIN (German Standard). In the production of Yaoda, the following standards are mainly encountered: GB30; GB5783; GB5782; GB52; GB6170; GB818; GB819; GB845; GB846; GB70; DIN912; DIN933; It has been replaced by GB5783 (new national standard). GB52 (old national standard) has been replaced by GB6170 (new national standard) in the standard book.
The main operation method of the embedded knurled copper nut of the lock nut is injection molding. After heating, it is embedded into the plastic part or directly injection molded. If injection molding is used, the melting point of P/NYLOY/PET is above 200°C. , After the embedded nut is hot melted into the plastic part, the temperature rises rapidly. After injection molding, the plastic body rapidly cools and crystallizes and hardens. If the embedded nut temperature is still at a high temperature, it may fall to the place where the copper nut contacts the plastic part. Start to loosen or crack. Therefore, copper nuts are used instead of carbon steel nuts in the injection molding of embedded nuts.
As shown in Figures 1 and 2, Yueluo is an automatic locking screw. From bottom to top, there are screw head 1 with external thread, screw rod and nut 3. The screw rod is a hollow screw rod 2, and the hollow screw There are long holes 7 on both sides of the rod 2, the width of the long hole 7 is smaller than the inner diameter of the hollow screw rod 2, and a spring 4 is arranged in the inner cavity of the hollow screw rod 2, and the spring 4 is not smaller than the hollow screw rod 2 in the free extension state. The upper end of the spring 4 is provided with a plug 5, the distance between the two wings 6 of the plug 5 is greater than the diameter of the nut 3, and the two wings 6 of the plug 5 protrude out of the hollow screw rod 2 through the long hole 7. When using the Yueluo, you only need to compress the spring through the two wings, insert the U-shaped clip after the neutral position is exposed, and then release the two wings, the spring will automatically return and compress the U-shaped clip, which is easy to use, safe and reliable. Claim 7. A self-locking screw, from bottom to top, is a screw head, a screw rod and a nut provided with an external thread, characterized in that the screw rod is a hollow screw rod, and both sides of the hollow screw rod are respectively provided with Long hole, the width of the long hole is smaller than the inner diameter of the hollow screw rod, the inner cavity of the hollow screw rod is provided with a spring, the upper end of the spring is provided with a plug, and the two wings of the plug protrude out of the hollow screw rod through the long hole.
Stainless steel nuts generally have or become loose during use, which mainly depends on the thread. As for the threaded sleeve, it is a new type of threaded fastener, which is a spring-shaped inner and outer thread concentric body precisely machined from stainless steel wire with high-precision diamond cross-section. Of course its performance is also very good. The following are the following methods of loosening stainless steel nuts: 1. On the mechanical parts loaded with metal or non-metallic materials (such as aluminum, magnesium and other light alloy engineering materials), it can form high strength, wear resistance, high precision standard internal thread. Such as applications: high-voltage switchgear, hydraulic machinery, welding equipment |, tobacco machinery, microwave communications, auto parts, air separation equipment, coal machinery, power machinery, textile and chemical fiber machinery, etc.
Riveting is a method for combining two pieces of metal. Therefore, riveting technology is often used to fasten rivets such as nuts or rivets to metal sheets.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: square key pins, national standard aluminum profile nuts, self-locking nuts, DIN928 square welding nuts and other products, we can provide you with suitable fasteners Firmware Solutions.
