The quick-install and quick-release nut uses the threaded block to move radially and axially along the inclined surface at the same time to achieve the cohesion and separation of the threaded block. However, the nut has a complex structure and is difficult to manufacture, and the internal and external threads may not be properly locked during use. Occurs, bearing capacity and reliability are poor.
In steelmaking plants, the wheels of metallurgical casting crane trolleys used for hanging liquid metal are connected with cardan shafts through flanges. Usually, a keyway is set in the radial direction of the connecting flange, and the keyway is a through groove. The B-type flat key is set in the keyway to transmit torque. During the frequent forward and reverse motion of the wheel, the flange connection bolts are easily loosened. Since the keyway is a through groove, the B-type flat key is easily caused when the flange connection bolts are loosened. It falls off from the keyway of the connecting flange and cannot transmit the torque, which seriously affects the working efficiency of the locomotive. In addition, because the B-type flat key falls off and cannot transmit the torque, the locomotive can only rely on the connecting bolt to transmit the torque when it continues to work. Poor, it is easy to damage and scrap the connecting bolts, and then damage the connecting flanges, requiring frequent replacement and maintenance, high cost, and difficult maintenance.
Many standoffs are used in sheet metal and aluminum profile processing. However, the existing pressure riveting nut column generally adopts a clearance fit between the pressure riveting and the pressed plate, which has no effect on the general pressure riveting, but it has high surface quality requirements for aluminum profiles, especially Painting aluminum profiles will have a certain impact. First, because the bottom holes of pressure riveting on aluminum profiles are generally processed on ordinary punching machines, a tapered hole with a horn will be generated, which will further increase the gap between the pressure riveting nut columns. Make the mutual tightening force smaller, causing some aluminum profile components to loosen the riveting nut when installing screws, resulting in unqualified surface quality. Therefore, we urgently need a way to reduce the matching gap with the bottom hole of the aluminum profile pressure riveting. The pressure riveting standoff is used to increase the wrapping force between the pressure riveting standoff and the aluminum profile hole.
According to the process, the wing nut can be divided into cold heading wing nut, casting wing nut and stamping wing nut. According to the shape, it can be divided into two basic shapes: square wing and round wing. According to the national standard number, it can be divided into GB/T62.2-2004 Square Wing Wing Nut Wing Nut Round Wing Wing Nut Round Wing GB/T62.1-2004 Round Wing Wing Nut
Metric threads are measured in MM (millimeters) and have a cusp angle of 60 degrees. Both US and Imperial threads are measured in inches. The cusp angle of the American thread is also 60 degrees, while the cusp angle of the imperial thread is 55 degrees. Due to the different units of measurement, the representation methods of various threads are also different. For example, M16-2X60 represents a metric thread. His specific meaning is that the nominal diameter of the screw is 16MM, the pitch is 2MM, and the length is 60MM. Another example: 1/4—20X3/4 means the inch thread, what he specifically means is the nominal diameter of the screw It is 1/4 inch (one inch = 25.4MM), there are 20 teeth on one inch, and the length is 3/4 inch. In addition, if you want to express American screws, UNC and UNF are usually added to the back of the British screws to distinguish between American coarse teeth or American fine teeth. In the usual domestic sales business, the most common standards we encounter are GB (National Standard) and DIN (German Standard). In the production of Yaoda, the following standards are mainly encountered: GB30; GB5783; GB5782; GB52; GB6170; GB818; GB819; GB845; GB846; GB70; DIN912; DIN933; It has been replaced by GB5783 (new national standard). GB52 (old national standard) has been replaced by GB6170 (new national standard) in the standard book.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: trapezoidal screw nuts, small square head bolts, manipulator adjustment handles, external hexagonal plastic bolts and other products, we can provide you with suitable tightening. piece solution.