your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Customized Grade 12.9 Black High Strength Hex Nut Hex Nut 1/2-13

author:[email protected] Click:6394end source: time:2022-10-23 08:37:30

Summary of information:We have more than ten years of production experience in the screw industry, the main products are: half hexagonal rivet ...

The performance grade 8.8 of stainless steel bolts refers to the material's tensile strength limit of 800MPa and yield limit of 640MPa. The performance grades of stainless steel bolts, studs and studs are divided into 10 grades: from 3.6 to 12.9. The number before the decimal point represents 1/100 of the tensile strength limit of the material, and the number after the decimal point represents 10 times the ratio of the material's yield limit to the tensile strength limit. There are 7 grades of performance grades for nuts, from 4 to 12. The numbers roughly represent 1/100 of the minimum stress that the stainless steel nut is guaranteed to withstand. For unified inch threads, there are three thread grades for external threads: grades 1A, 2A and 3A, and three grades for internal threads: grades 1B, 2B and 3B, all of which are clearance fits. The higher the rating number, the tighter the fit. Classes 1, 1A and 1B, very loose tolerance classes, which are suitable for tolerance fits of internal and external threads. Grades 2, 2A and 2B are the most common thread tolerance grades specified for inch series mechanical stainless steel fasteners. Grades 3, 3A and 3B, screwed together to form the tightest fit, suitable for tight tolerance stainless steel standard parts, for safety critical designs. Metric threads, there are three thread grades for external threads: 4h, 6h and 6g, and three thread grades for internal threads: 5H, 6H, 7H. Thread fit is best combined into H/g, H/h or G/h. For bolts, stainless steel nuts and other refined fastener threads, the standard recommends 6H/6g fit. Carbon steel: The strength grade is marked by ? It consists of two separated numbers. The meaning of the number part before the ? in the marking code represents the nominal tensile strength, for example, 4 in grade 4.8 represents 1/100 of the nominal tensile strength of 400N/MM2. The meaning of the ? and the number part after the point in the marking code represents the yield-strength ratio, that is, the ratio of the nominal yield point or the nominal yield strength to the nominal tensile strength. For example, the yield point of grade 4.8 products is 320N/mm2. The strength grade mark of stainless steel products consists of two parts separated by —. The symbol before — in the sign code indicates the material. Such as: A2, A4 and other signs — indicate strength, such as: A2-70 Carbon steel: The mechanical properties of bolts can be divided into: 3.6, 4.6, 4.8, 5.6, 5.8, 6.8, 8.8, 9.8, 10.9, 12.9 in total 10 performance levels

Further, it also includes a motor, the motor is provided with a thruster that makes the cutting wheel move towards the conveying device, the other end of the motor is provided with a bearing, the output end of the motor is provided with a special-shaped wheel, the special-shaped wheel is toothed with the bearing, and the motor drives the special-shaped wheel to rotate. , move the cut-off wheel closer to or away from the conveyor.

T-bolts have been widely used in the fields of aviation, aerospace and defense due to their good positioning and anti-shedding effects. Its related standards have special requirements for accurate positioning, anti-falling off, and dimensional consistency of T-bolts. This requires that the position, size and shape and position tolerance of the anti-fall hole of the T-bolt shank must be controlled within a certain range. Therefore, the processing method of the anti-shedding hole is particularly important. Since the machined anti-shedding hole is located at the position of the rod, the milling processing efficiency is too low, the product cost is high, and there is a large machining error. When conventional drilling is used, the consistency of the anti-shedding hole size cannot be guaranteed. To solve the above problems of low efficiency and dimensional instability

At present, there are many kinds of smart terminals on the market. Due to the reduction of the overall volume of the smart terminal and the more compact internal parts, the nuts are generally made of injection-molded nuts. The traditional injection-molded nuts are directly fixed on the equipment. During the process, it is easy to loosen and fall off, which greatly reduces the service life of the injection nut and brings inconvenience to the use of the mobile terminal.

Advantages of anti-loose washers 1. Ensure that the clamping force of the connection is still maintained under strong vibration, which is better than fasteners that rely on friction to come from the lock; 2. Prevent the loosening of bolts caused by vibration, which no longer occurs due to fasteners related problems caused by loosening; 3. No special installation work is required, and it is easy to install and disassemble; 4. The temperature changes will not make the connector loose; 5. Durable; 6. Reusable.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: thin flat head furniture screws, fastener screws, barb four-corner nails, Dongguan Yueluo and other products, we can provide you with suitable fastening products piece solution.

black high strength

Custom Level 12.9


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].