your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Supply GB93 black 8-level spring washer spring washer black spring washer open washer black spring washer

author:[email protected] Click:7654end source: time:2022-11-08 19:06:32

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: cross flat head machi...

Screw model Drive Code: groove on the head, characteristic model Length Code: screw length (mm) A-1: Thread Code: screw model Metric screws directly indicate the screw model with the outer diameter of the screw, such as M3, the outer diameter of the screw is 3.00mm. ; M4 means the outer diameter of the screw is 4.00mm. Metric Thread Size x Pitch: Note: The metric screw is behind the screw model, and sometimes the screw pitch is indicated. Such as M3x0.5, M4x0.70, M5x0.8, M6x1. Standard specification, usually not mentioned. A-2: Length Code: Screw length: For metric screws, the screw length is directly marked in mm. The total length of the screw is marked, only the length below the head is calculated, excluding the head height. But With the exception of flat head screws, the total length of the screw is marked with the head height. A-3: Drive Code/ Head Groove, Features.

Riveting is the most traditional way of connecting metal parts. It has the advantages of easy operation, high reliability and not easy to deform. It is widely used in the skeleton of outdoor products such as tents and camp beds. Commonly used aluminum alloy rivets use their own deformation or interference to connect the parts of the riveted parts in the riveting process. Due to cost and functional considerations, the rivet and the riveted material are often different, which is easy to occur in outdoor high humidity. Electrochemical corrosion, and the commonly used high-strength thin-walled pipes have a large shear stress on the aluminum alloy rivets at the riveting point. Under the combined action of the above two factors, it is easy to cause deformation or even breakage at the riveting point, which affects the life of outdoor products. A kind of Corrosion and shear resistant aluminium alloy rivets.

In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35 , and the screws enter the screw accommodating hole 41 from the discharge port through the guide rail 6 . The slotting is carried out, which improves the efficiency and saves the labor cost.

Anti-corrosion technology Stainless steel screws are made of metal, and there are four main methods for metal anti-corrosion, namely the properties of the material itself, the environment of use, the interface between materials and the environment, and the improvement of the metal structure design. If a complete anti-corrosion alloy is used to make stainless steel Screws, unless there is a special need, are not cost-effective in terms of economics, and it is also impractical to completely isolate the appearance of the screw from environmental elements that can cause corrosion. Improving the metal structure design can improve the influence of special circumstances under certain conditions, but the design of most stainless steel screws cannot be fully corrected, and its maintenance effect is not permanent, so this method cannot basically solve the problem, as long as it is on the surface. Top anti-corrosion, that is, surface anti-corrosion treatment is the most widely used method. The anti-corrosion treatment on the surface of stainless steel screws refers to the use of various methods to apply a protective layer on the metal surface. The purpose of avoiding or mitigating corrosion. The protection layer should be able to meet the following requirements: 1. Corrosion resistance, wear resistance, high hardness, 2. The structure is tight, intact, and the pores are small. 3. It has strong separation and good adhesion with the base metal. 4. It is evenly distributed and has a certain thickness. The maintenance layer is usually divided into two types: metal coating and non-metallic coating. Metal coating refers to the use of metal or alloy with strong corrosion resistance to form a maintenance layer on the surface of metal that is easy to corrode. This coating is also called plating. There are quite a few methods and varieties to produce metal coatings, the most common of which is electroplating, followed by molten metal immersion plating (hot dipping) and chemical surface treatment. Non-metallic coating refers to the use of organic polymer materials such as paint and inorganic materials such as ceramics to form a protective layer on the surface of metal equipment or parts. The protective layer can completely isolate the base metal from the environmental medium and prevent the base metal from corrosion due to contact. Corrosion is formed in the medium of stainless steel standard parts.

3. Friction coefficient The friction angle is an important factor affecting the torque, and the existence of friction is the basis for the normal operation of the lock nut. When the lock nut is working, the contact surface has pressure and friction under the action of the elastic restoring force of the thread piece. During the repeated use, the rough position and edges and corners of the contact surface are ground and smoothed under the action of cyclic friction. The coefficient of friction becomes smaller, which in turn reduces the maximum unscrewing torque of the nut.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: embedded nuts, cylindrical pin positioning pins, GB823 round head screws, reed nuts wholesale and other products, we can provide you with suitable products Your fastener solution.

spring washer

Supply GB93 black 8-level spring pad


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].