your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Custom-made core-pulling rivets aluminum pull rivets aluminum round head heart-pulling rivets pull nails 3/8 5/8

author:[email protected] Click:7755end source: time:2022-10-25 21:44:32

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: 0 stainless steel scr...

The circlip travel mechanism includes a travel cylinder and a travel plate connected with the push rod of the travel cylinder; the travel air cylinder can control the travel plate to be inserted into the circlip press-out and positioning mechanism, and the circlip lifting and tightening mechanism; the travel plate The surface of the device is provided with a groove for placing the circlip; the height of the groove is the height of one circlip.

Heat treatment broadcast quenching and tempering HB220-270, nitriding HRC>65 foreign use titanium carbide coating method to improve the corrosion resistance of the screw surface, but according to reports, its wear resistance is not good enough. A series of measures have been taken abroad to improve the wear resistance and corrosion resistance of the screw. One way is to use highly wear-resistant and corrosion-resistant alloy steel. Such as 34CrAlNi, 31CrMo12 and so on. There is also a method of spraying Xaloy alloy on the surface of the screw. This Xaloy alloy has high wear and corrosion resistance.

Comparing the physical properties of stainless steel and carbon steel, the density of carbon steel is slightly higher than that of ferritic and martensitic stainless steel, but slightly lower than that of austenitic stainless steel; the resistivity is based on carbon steel, ferritic, martensitic and The order of austenitic stainless steel is increasing; the order of linear expansion coefficient is similar, austenitic stainless steel is the highest and carbon steel is the smallest; carbon steel, ferritic and martensitic stainless steel are magnetic, austenitic stainless steel is non-magnetic, But its cold work hardening will generate magnetism when it is transformed into intensite, and heat treatment method can be used to eliminate this martensitic structure and restore its non-magnetic properties. Compared with carbon steel, austenitic stainless steel has the following characteristics: 1) High electronegative rate, which is about 5 times that of carbon steel. 2) The large coefficient of linear expansion is 40% larger than that of carbon steel, and with the increase of temperature, the value of the coefficient of linear expansion of stainless steel screws increases accordingly. 3) Low thermal conductivity, about 1/3 of carbon steel.

Among them, the pneumatic riveting machine is more commonly used. The pneumatic riveting machine is also equipped with a clamp for assembling the rivet. The existing clamp usually uses two rotating clamps for fastening and assembly, but the rotation easily causes the two clamps to buckle. Misalignment, thus affecting the assembly of the rivet.

The paint mixing mixer used for color matching in the auto repair industry uses a multi-link connection transmission as the main driving force. The transmission of torque has higher quality requirements for the impact resistance and fatigue resistance of the cotter pin. During the use of the cotter pin, it was found that the cracking phenomenon occurred due to insufficient strength, resulting in the machine not running. In the existing multi-link transmission mode of the paint mixing mixer, the connecting rod drives more than 10 paint pots in each layer of the frame to stir, and the bottom connecting rod is also responsible for the transmission of the torque of the upper connecting rod, which leads to the connection between the connecting rod and the connecting rod. The pins connected by the rods must have strong impact resistance and fatigue resistance, and must have a certain anti-loosening function.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: lifting ring nut, grade 4 hexagon nut screw and nut, all-steel rivet, self-locking nut and other products provided by manufacturers, we can provide you with suitable products for you. Fastener Solutions.

Aluminum pull rivets

Customized blind rivets


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].