your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Wholesale Nickel Plated Round Head Three Combination Screws Pan Head Cross With Pad Combination Screws Carbon Steel Electronics

author:[email protected] Click:8208end source: time:2022-09-26 06:33:36

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: carbon steel knurled ...

There are many types of T-bolts used with pre-embedded chutes, which are used for the connection of external components of pre-embedded chutes embedded in segments, U-beams, building concrete, etc. The fixing of the chute on the forming die. When producing segments and U-shaped beams, the embedded chute is fixed on the forming mold by T-bolts. During the concrete pouring process, the tightening nut is easily covered by concrete. In this way, the concrete on the fastening nut should be removed, but it is difficult to remove the concrete, which will cause inconvenience to the disassembly of the forming mold after the production of the segment and the U-shaped beam.

screw can be equipped with only one spring washer or only one flat washer, or it can also only be equipped with a two-piece combination of flower teeth. The national standard number of the combination screw is represented by GB9074. The commonly used cross recessed small pan head three combination screw national standard is GB9074.8.

With the continuous strengthening of infrastructure construction, the continuous increase of construction scale and the complexity of construction, the particularity of the requirements for construction equipment, materials, tools and equipment is also getting higher and higher, such as buildings, power stations, railway tunnels The channel steel used in these special construction environments requires the use of a special bolt, which must be easy to put in, easy to use

rotating rod is rotatably installed on one side of the two pillars that are close to each other, and a second bevel gear is welded on the ends of the two rotating rods that are close to each other. The two second bevel gears are meshed with the two first bevel gears respectively. , The first sprocket is welded on the two rotating rods, the chain is meshed on the two first sprockets, and the screw rods are installed on the sides of the two pillars that are close to each other. Above the rod, the second sprockets are welded on the two screw rods, the two second sprockets are connected to the two first sprockets through two chains respectively, and threaded blocks are threaded on the two screw rods. The sides of the two threaded blocks close to each other are symmetrically welded with connecting columns, and the sides of the four connecting columns close to each other are welded with movable rods respectively. The other ends of the support plates are respectively rotatably installed with the same support plate, and the assembly device body is fixedly installed on the top of the support plate.

screw with a gasket aims to provide a screw with a gasket that improves installation efficiency. The technical solution of the screw is that after the screw cap, the connecting rod and the screw rod are processed, the gasket with the installation through hole is processed. The installation through hole is drilled through the connecting rod, and then the end of the screw rod opposite to the connecting rod is processed to form a convex tooth structure by extrusion. At the same time, the outer diameter of the tooth peak of the convex tooth is larger than the inner diameter of the installation through hole, so that the gasket is not easy to be installed. Falling off, the step of manually wearing the gasket is reduced, that is, the workload of the staff is reduced, and the installation efficiency is relatively high. The flange increases the contact area between the screw cap and the gasket, and enhances the friction between the screw cap and the gasket, which can prevent the screw from loosening easily after being fastened and installed, thereby improving the connection stability of the screw. When installing the screw, the fixing part can be snapped into the fixing groove on the installation plane, so as to avoid the washer from rotating with the rotation of the screw when the screw is tightened, which is convenient for the tightening and installation of the screw.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: national standard washers, hexagon socket bolts, external hexagon auto parts screws, hexagon screws and other products, we can provide you with suitable fastener solutions for you Program.

Round head three combination screw

Wholesale Nickel Plating


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].