your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Production of diamond pattern aluminum column connection long nut FPV model rack double inner tooth mesh nut 3/8

author:[email protected] Click:8244end source: time:2022-12-08 15:50:50

Summary of information:We have more than ten years of production experience in the screw industry. The main products are: hand-tight screws, GB...

The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to overcome the above-mentioned shortcomings of the prior art, and provide a hidden screw fastener, which avoids the defect that the screw end cap is directly exposed when the traditional screw is tightened, which affects the appearance. Washers and shields hide the end caps of the screws, which are both beautiful and insulating, preventing the screws from rusting, and avoiding scratches due to burrs on the ends of the screws, which are not only beautiful but also practical and safe.

Washers are accessories used between the nut and the connecting piece to disperse the pressure of the nut on the connected piece, thereby protecting the connected piece. The general gasket is a flat gasket, which is easy to loosen after long-term use, and the stability is not high. There are also some elastic washers, which have poor elastic stability and short service life.

1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.

The opening circlip is widely used in many industrial fields and plays a role in limiting the position of the parts. When in use, as long as the circlip is installed in the circlip groove of the part, the position of other matching parts can be effectively limited, so as to avoid the axial displacement of the matching parts. Since some opening circlips do not have circlip pliers installation holes, circlip pliers cannot be used and can only be installed by hand, which not only cannot effectively ensure the installation quality of the circlip, but also limits the efficiency of installation work.

A T-shaped grounding bolt comprises a connection platform, a hexagonal bolt is welded below the described connection platform, and the lower surface edge of the described connection platform is provided with a barb.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: Washers open stop washers, knurled aluminum alloy single-layer hand-tightened nuts, precision machinery, accessories-type slider shrapnel and other products, we can Provide you with the right fastener solution for you.

connecting long nut

Production of diamond-patterned aluminum columns


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].