your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Customized aluminum alloy washer, high-gloss gasket, enlarged and thickened screw, flat gasket, metal washer

author:[email protected] Click:8133end source: time:2022-12-10 01:11:02

Summary of information:We have more than ten years of production experience in the screw industry, the main products are: metal screw gasket, b...

Usually, a tight fit is used between the cylindrical pin and the pin hole, such as the cooperation between the cylindrical pin and the pin hole on the rotating shaft of the motor. Due to the tight fitting structure between the cylindrical pin and the pin hole, the shaft with the pin hole needs to be well positioned during assembly, and then the cylindrical pin is aligned with the pin hole, and then knocked or pressed to fit. The cylindrical pin is pressed into the pin hole. There is no device specially used for the installation of cylindrical pins in the prior art, and two or more people are required to cooperate to install the cylindrical pins into the pin holes. installation quality.

With the advancement of technology in various industries, the current structural design of screws has evolved from just simple locking to focusing on work efficiency during the locking process and not destroying the integrity of the objects to be locked. The new cases such as No. 556784 screw improvement and No. 289405 screw that integrates locking, stability, labor-saving, fast and multi-function which were previously designed and approved and published in the Central Taiwan Bulletin are the main representatives of screws. It is clear that It is learned that the two cases not only fully improve the shortcomings of the traditional simple locking screws, but also achieve the purpose of substantial improvement of the screws designed in each case in actual use.

As my digital TV technology becomes more and more mature, more and more people with digital-to-analog signal conversion function enter people's lives. Therefore, the number of production and processing is also increasing day by day. There are many requirements for the form, reliability and cost of PCB fixing screws in production. One of the existing fixing methods is to fix by means of bolts and nuts. The operation steps are to place the PCB board on the inner threaded copper column connected to the casing, and pass through the bolts with fine teeth. Screw holes on the PCB board, and then fix them on the copper posts with nuts. The connection method of this solution is reliable, but its manufacturing cost is high, and the copper column and the metal shell need to be screwed together, resulting in low production efficiency and high cost. In addition, there is also a common way that the PCB is supported by a plastic column, and the self-tapping screw is passed through the screw hole on the PCB board, and the PCB board and the metal bottom shell are connected by the self-tapping thread on the screw. The main disadvantage of this solution is that after the screw is fixed on the metal shell, the screw head is exposed at the bottom of the machine. If the user is not careful during use, the hand scratching phenomenon will occur, which will bring changes and harm to the user's use. . And when the machine slides on the desktop, if the screw head is too exposed, it will scratch the desktop. Therefore, how to provide a PCB fixing method with convenient operation, reliable connection and low production cost is a technical problem to be solved urgently in the industry.

In order to achieve this purpose, the rivet nut is cold extruded from low carbon steel, the brim is cold forged, the deformed skirt is extruded in the die, and the threaded hole is extruded at the lower end of the deformed skirt. It is characterized in that it consists of a brim, a deformed skirt and a threaded hole. There are fish teeth below the brim; the outer side of the lower end of the threaded hole has a lead angle; the cross section of the thread on the inner wall of the threaded hole is an isosceles trapezoid, and the upper bottom of the trapezoid is a concave arc. Thus, the riveted object is tightly connected with the rivet nut.

The bolt thread is generally cold worked, so that the thread blank within a certain diameter range passes through the rubbing (rolling) wire plate (die), and the thread is formed by the pressure of the wire plate (rolling die). The plastic streamline of the threaded part is not cut off, the strength is increased, the precision is high, and the quality is uniform, so it is widely used. In order to make the outer diameter of the thread of the final product, the required thread blank diameter is different, because it is limited by factors such as thread accuracy and whether the material is coated or not. Rolling (rubbing) thread is a processing method that uses plastic deformation to form thread teeth. It uses a rolling (screwing plate) die with the same pitch and tooth shape as the thread to be processed, while extruding the cylindrical screw blank, while rotating the screw blank, and finally transferring the tooth shape on the rolling die to the On the screw blank, the thread is formed. The common point of rolling (rubbing) thread processing is that the number of rolling revolutions does not need to be too much. If it is too much, the efficiency will be low, and the surface of the thread teeth will easily cause separation or random buckle. On the contrary, if the number of revolutions is too small, the diameter of the thread is easy to be out of round, and the pressure at the initial stage of rolling increases abnormally, resulting in a shortening of the life of the die. Common defects of rolled threads: cracks or scratches on the surface of the thread part; random buckles; out of roundness of the thread part. If these defects occur in large numbers, they will be discovered during the processing stage. If the number of occurrences is small, the production process does not notice these defects and then circulates to users, causing trouble. Therefore, the key issues of processing conditions should be summarized, and these key factors should be controlled in the production process.

We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: small flat washers, countersunk head socket head cap screws and bolts, straight-through nylon bushings, tooth rods through wire screws and other products, we can provide you with suitable products Your fastener solution.

High gloss spacer

Custom Aluminum Washers


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].