your location: 首页>>News>>Industry News

Service Hotline

+86760-8787 8587

Production of retaining ring retaining ring for carbon steel hole C-shaped clamping elastic inner retaining ring for C-shaped split shaft

author:[email protected] Click:9452end source: time:2022-11-22 16:28:32

Summary of information:We have more than ten years of experience in the production of screw industry, the main products are: equal-length screw...

Yueluo also provides a thin plate rivet structure, which includes a metal thin plate and a rivet. The metal sheet is provided with a riveting hole; the riveting piece is penetrated in the riveting hole, the outer edge of the riveting piece is provided with an occlusal structure, and the inner edge of the riveting hole is embedded with the occlusal structure. A deformation groove is provided on the metal sheet, and the deformation groove is adjacent to the rivet hole.

At present, in the era of industrialization, rivets used in specific occasions, automobiles, and aviation industries can only rely on professional tools and equipment to complete the riveting method.

Lock washers feature easy installation. 1. Just place the helical tooth surfaces on the inner side of the two washers against each other and place them between the nut and the connecting material; 2. After the nut is tightened, the radially convex surface on the outer side of the lock washer and the contact surfaces at both ends are in an engaged state, and The angle of the slope angle of the helical tooth surface on the inner side of the washer is greater than the thread angle of the bolt; 3. When the bolt is elongated due to mechanical vibration, the nut will rotate and loosen accordingly. Because the frictional force of the outer radial convex surface of the lock washer is greater than the frictional force between the inner helical tooth surfaces. In this state, only the relative dislocation between the inner helical tooth surfaces is allowed to generate a certain lifting tension; 4. When the bolt shrinks, the helical tooth surface of the washer will make the nut return to its original position. So as to achieve 100% anti-loose and tightening effect; 5. Washers are suitable for relatively flat and smooth surfaces; 6. If the connecting material is non-metallic material, a metal plate can be fixed on the connecting material, so that the Use the lock washer; 7. There is no need to use a torque wrench when installing the lock washer; 8. You can choose to use an air tool when installing or removing the lock washer.

At present, the screws used by people are not provided with a device that does not loosen, especially in some key parts, if the screws are loosened, it will cause heavy losses. In order to overcome the current situation, there is no device on the screw to prevent the screw from loosening, which may cause heavy losses. Guangdong Yueluo Hardware Industry Co., Ltd. The inner part will not be loose, and it will save people the trouble of maintenance and reduce the hidden danger of accidents. The solution adopted by Guangdong Yueluo Hardware Industry Co., Ltd. to solve its technical problems is to make a special screw and nut, set a stop groove on the screw, and then set a stop rod on the nut. After the screw is tightened , let the backstop rod be stuck in the backstop groove to prevent the screw from loosening. The beneficial effect of Guangdong Yueluo Hardware Industry Co., Ltd. is to ensure that the screws will not loosen during the service period, reducing the hidden danger of accidents and reducing the maintenance rate. Guangdong Yueluo Hardware Industry Co., Ltd. is further described below in conjunction with the accompanying drawings and embodiments

Generally, the countersunk head is used in places where the surface is required to be smooth without protrusions, because the countersunk head can be screwed into the part. Round heads can also be screwed into parts. The tightening force of the square head can be larger, but the size is large. In addition, in order to meet the needs of locking after installation, there are holes in the head and holes in the rod. These holes can prevent the bolts from loosening when they are vibrated. Some bolts without threads should be made thin, called thin-waisted bolts. This kind of bolt is beneficial to the connection under variable force. There are special high-strength bolts on the steel structure, the head will be larger, and the size will also change. In addition, there are special uses: for T-slot bolts, which are most used on machine tool fixtures, with special shapes, and both sides of the head should be cut off. Anchor bolts, used for machine and ground connection and fixing, come in many shapes. U-bolts, as previously described. and many more. There are also special studs for welding. One end has a thread and the other end is not. It can be welded to the part, and the other side can directly screw the nut.

We have many years of experience in the production and sales of screws, nuts and flat washers. Your fastener solution.

circlip

Production of retaining rings for carbon steel holes


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].