As we all know, when installing the outdoor unit of the air conditioner, most of the installers need to hang it on the outer wall. When tightening the machine foot screws, they all need to lean out of the window or climb out the whole person, and use a wrench to tighten it. . Therefore, it is difficult for the installer to operate, and it is easy to drop the installation materials such as screws and nuts, which is not only a waste of materials, but also easy to hurt personnel. The purpose of Guangdong Yueluo Hardware Industry Co., Ltd. is to solve the above problems, and provide a safe and labor-saving air conditioner outdoor unit machine foot screw installer that the installer does not have to lean out of the window or climb out of the room, and the installation materials are not easy to fall.
Usually, the car wheel is fixed on the axle sleeve with positioning pins and pins, and the tire hub and the sleeve are fastened on the axle with locking nuts, lock washers, and adjusting nuts. This structure can operate normally within a certain period of time when the vehicle speed is low and the vibration is small. However, when the car runs for a long time, especially when the road surface is uneven and the load changes sharply, the axle sleeve bears a great impact. Once the shear force generated is too large, the pin will break, and the nut will be loosened. Affected, the wheel and hub will be loose. If the maintenance is not timely, or the driver is inexperienced, the car will have an accident in which the tire falls off with the wheel hub. This is extremely dangerous. So people are looking for ways to prevent wheels and hubs from falling off
Many parts on the car need to be rubberized, which can reduce noise, especially the parts related to shock absorption. Nuts are welded on many of these parts to facilitate the installation of other parts on them. The sheet metal is generally relatively thin, and most of them are only one or two millimeters. A through hole is punched, and then the nut is placed in the hole, and then around it. Spot welding is done so that it can be fixed. After spot welding, the periphery of the screw hole on the sheet metal will not be flat due to thermal deformation, which will affect the appearance.
The circlip is a common limiting element in the mechanical field, which is mainly used to limit the axial limit of mechanical parts. At present, the common circlips on the market are all circular rings with an opening. The circular ring has a certain elastic deformation capacity. When in use, the circlip can be detachably assembled to the mechanical on the part. However, the defect of the circlip adopting the one-piece ring is that the circlip is easily broken when frequently disassembled and used, and the service life is short.
T-bolt is a common fastener, which is mostly used where there is a T-slot on the workbench or where the connection can only be made from the side to be connected. However, it has the following problems in the actual production and processing process. 1. The T-bolt manufactured according to the current GB37-88 is used in conjunction with the T-slot on the worktable, which is easy to damage the T-slot on the worktable. 2. According to the observation and investigation, it is found that 90% of the damage to the T-bolt manufactured by GB37-88 is thread damage during use, and the T-shaped part is rarely damaged, resulting in a waste of raw materials. SUMMARY OF THE INVENTION The purpose of the present invention is to solve the problem that the current composite T-bolt is easy to damage other equipment and cause waste of raw materials in the actual use process, and to provide a simple structure, easy to use, safe and reliable, and not easy to damage other equipment. , thereby saving raw materials and other advantages of composite T-bolts. In order to achieve the above purpose, the present invention adopts the following technical scheme: a composite T-bolt, which includes a bolt, and one end of the bolt is connected with the T-shaped block cockroach. The T-shaped block is provided with a tapered hole, and the connection between the bolt and the T-shaped block is a cone, which is matched with the tapered hole. The utility model combines the two parts of the T-shaped block and the threaded bolt through the T-shaped block and the taper hole and the cone on the bolt to automatically lock the two parts before use. When the threaded part of the bolt is damaged, only the threaded bolt needs to be replaced. That's it. Compared with the domestic T-shaped bolts currently produced in the manufacturing process, the utility model solves the problems of complicated manufacturing processes and waste of raw materials. It is well known that the manufacture of T-bolts requires processing such as forging, turning, milling, and heat treatment. Since the composite T-bolt is used in combination with the T-block and the bolt, and the T-block is rarely damaged, after purchasing or manufacturing the T-block once, you only need to purchase or manufacture the bolt in the future. Compared with the T-bolts currently produced in China, the composite T-bolts can better protect the T-slots on the working surface. Because the T-bolt currently produced in China will rotate a certain angle around the axis of the T-bolt when fixing the object, the T-bolt will rotate at a certain angle, thereby reducing the contact between the T-bolt T-shaped surface and the T-slot stress surface of the working face. surface, causing stress concentration on this surface. The composite T-bolt avoids the above problems due to the increase of the guide surface, thereby protecting the T-slot. The beneficial effects of the utility model are: 1. Saving raw materials. 2. Reduce processing costs. 3. Simplify the technological process. 4. Protect the T-slot.
We have many years of experience in the production and sales of screws, nuts, flat washers, etc. The main products are: T-shaped marble nuts, nickel-plated copper screws, JISB1255 washers, scooter conversion screws and other products, we can provide you with suitable fastening for you piece solution.