What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Service Hotline
+86760-8787 8587We have more than ten years of experience in screw industry production, the main products are: metric countersunk head knurled nut, R type cotter pin, ingot casting nut 0, full hollow rivet, copper nut screw, practical connector square female nut, GB109 copper flat head Rivets, plastic round enlarged flat washers, DIN912 bolts, large cap pull rivets, flat head copper studs through holes, 4.8 grade GB52 carbon steel natural hexagon nuts, national standard GB812 round nuts, 4.8 grade hexagonal galvanized nuts, camera screws, etc. Due to the different materials and specifications of the products, the prices are also different, if necessary, please contact us.
In another embodiment of Guangdong Yueluo Hardware Industry Co., Ltd., the discharge port of the vibrating plate 2 is matched with the screw receiving hole 35, and the screws can enter the screw receiving hole 35 through the discharge port after sorting and sorting in the vibrating plate 2. . Preferably, a guide rail 6 is provided between the discharge port of the vibrating plate 2 and the screw accommodating hole 35 , and the screws enter the screw accommodating hole 43 from the discharge port through the guide rail 6 . The slotting is carried out, which improves the efficiency and saves the labor cost.
Iron two combination screws can be sucked up with magnets, but stainless steel two combination screws are difficult to be sucked up. Environmentally friendly three-combination screws and non-environmentally friendly ones are invisible to the naked eye and require mechanical testing. It cannot be judged with the naked eye and out of thin air. The specifications of the two combination screws need to be determined by the national standard. The salt spray of the two combination screws needs to be measured with a salt spray machine for how many hours.
Countersunk head screws are mostly used after installation, and the surface of the parts cannot be raised, and the parts to be fastened have two thicknesses. Thickness, after the screw is tightened, there is still a part of the screw thread that does not enter the threaded hole. In this case, the countersunk head screw can definitely be tightened. There is usually a situation where the thickness of the fastened part is less than the height of the head of the countersunk head screw, which is commonly seen in sheet metal parts in mechanical equipment, such as the connection between the hinge of the chassis and the door and the box; the sheet metal of the equipment The connection of the cover to the equipment, etc. Due to the small thickness of the part, the tightened sheet metal part, the screw through hole completely becomes a conical hole, in this case, when the countersunk head screw is tightened, the screw head is not a tapered surface to press the sheet metal part , but the bottom of the screw head and the top of the threaded hole are squeezed. Although it feels that the screw is tightened, the sheet metal part is stuck instead of being pressed. In this case, although it feels that the screw is tightened, the sheet metal The gold pieces were indeed not tightened. This is a very common situation. Let’s talk about the reasons for the processing: the head cone of the countersunk screw has a 90° conical angle, and the apex angle of the newly bought drill is usually 118°-120°. Some workers who lack training do not know this angle is poor. It is often used to ream the hole with a 120° drill bit, which results in that when the countersunk head screw is tightened, it is not the conical surface of the head, but a line at the bottom of the screw head, which is one of the reasons why the so-called countersunk head screw cannot be tightened. , it's not the screw's fault.
At present, the automatic nailing device on the domestic market lacks the restraint and arrangement of the rivets when they are out of the nailing device, which makes the rivets irregular and uncontrollable after the automatic nailing is completed, which has adverse effects on on-site use and maintenance, and is unstable. .
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
What is the tolerance range of precision screws?
How to choose the right stainless steel screw manufacturer?
Why is there an R angle under the head of the hexagon head s...
We have more than ten years of production experience in the ...
We have more than ten years of experience in the production ...
We have more than ten years of experience in the production ...
We have more than ten years of experience in screw industry ...