Wholesale 201 stainless steel pan head hexagon socket bolt pan head hexagon socket screw umbrella type round head screw 1/2-13

We have more than ten years of production experience in the screw industry, the main products are: small hexagon head reamed hole bolts, trimmed hexagon copper machine screws, cold pier pressure riveting nuts, air conditioning bracket screws and screws, wholesale DIN934 nuts, percussion flat caps Liuding GB869 Countersunk Head Rivets, Nut Set Combination Bolts, Thickened Square Washers, Spaced Circuit Board Wiring Copper Posts, Countersunk Head Machine Thread Bolts, Gasket POSH Bolts, Full Tooth Cylinder Head Screws, Slotted Screws, DIN7971 Round Nuts, Fasteners such as insulating plastic bolts have different prices due to different product materials and specifications. Please contact us if necessary.

Online consultationMobile hotline
132 6870 6820
Product introduction

Screw Specifications

Screw head table

At present, when using the existing screwdriver to install the screw, it is necessary to fix the screw with the left hand and turn the screwdriver with the right hand. However, in some places where the installation space is small and the installation is difficult, there are many areas that cannot be accessed by hands, and the installation is very difficult. For example, on an airplane, when installing with a common screwdriver, it is very difficult to install the screws and the installation efficiency is low because the screws cannot be positioned; in addition, when installing screws on the aircraft wing or fuselage, the combination between the screwdriver and the screw is easy to slip, The blade of the screwdriver slipped out and could easily bruise the hand and damage the aluminum skin of the aircraft.

Wholesale 201 Stainless Steel

People often think that magnets attract stainless steel to verify its pros and cons and its authenticity. If it does not attract non-magnetism, it is considered to be good, and it is genuine; if it is magnetic, it is considered to be counterfeit. In fact, this is an extremely one-sided, unrealistic and wrong identification method. There are many kinds of stainless steel screws, which can be divided into several categories according to the organizational structure at room temperature: 1. Austenite type: such as 304, 321, 316, 310, etc.; 2. Martensite or ferrite type: such as 430, 420, 410, etc.; Austenite type is non-magnetic or weakly magnetic, and martensite or ferrite is magnetic. Most of the stainless steel usually used for decorative tube sheets is austenitic 304 material, which is generally non-magnetic or weakly magnetic, but may also appear magnetic due to fluctuations in chemical composition or different processing conditions caused by smelting, but this cannot be considered as a Counterfeit or substandard, what is the reason for this? As mentioned above, austenite is non-magnetic or weakly magnetic, while martensite or ferrite is magnetic. Due to component segregation or improper heat treatment during smelting, a small amount of martensite or ferrite in austenitic 304 stainless steel will be caused. body tissue. In this way, 304 stainless steel will have weak magnetism. In addition, after cold working of 304 stainless steel, the structure will also be transformed into martensite. The greater the cold working deformation, the more martensite transformation, and the greater the magnetic properties of the steel. Like a batch of steel strips, Φ76 tubes are produced without obvious magnetic induction, and Φ9.5 tubes are produced. The magnetic induction is more obvious due to the large deformation of the bending and bending. The deformation of the square rectangular tube is larger than that of the round tube, especially the corner part, the deformation is more intense and the magnetic force is more obvious. In order to completely eliminate the magnetic properties of 304 steel caused by the above reasons, the stable austenite structure can be restored by high-temperature solution treatment, thereby eliminating the magnetic properties. In particular, the magnetic properties of 304 stainless steel caused by the above reasons are completely different from those of other materials such as 430 and carbon steel, which means that the magnetic properties of 304 steel always show weak magnetic properties. This tells us that if the stainless steel strip is weakly magnetic or completely non-magnetic, it should be judged as 304 or 316 material; if it is the same as carbon steel, it shows strong magnetism, because it is judged as not 304 material.

Pan head hex socket head bolts

Pan head socket head cap screws

structure for concealing installation screws, comprising a locking piece, a driving piece, a bottom plate, a blocking cover and a handle head, the lower ends of the two locking pieces are provided with positioning holes, and the locking pieces pass through the positioning holes and the locking piece positioning posts on the base The occlusal and fixed, the middle of the two locking pieces is provided with a protruding point, the movable groove of the driving piece corresponds to the protruding points of the three locking pieces for fixing, the riveting point holes and screw holes of the bottom plate and the riveting points of the base The position that matches the screw holes and is fixed by screws, the blocking cover is directly inserted into the bottom plate, and the blocking cover is fixed by the rotating drive piece, the handle head is inserted into the base, and the slot of the handle head moves to the locking piece at the locking piece Lock the handle.

Umbrella Round Head Screws

Fasteners are an indispensable necessity in our lives and are used to flexibly fix two objects. However, in applications such as automobiles, large construction machinery and factories, the nuts often come loose and then fall off, resulting in frequent dangers and great dangers. Threats to people's lives and property.

1/2-13

The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].

Cooperation Case

Hot Recommend