Processing cup head hexagon socket self-tapping screw nickel-plated cylindrical head socket hexagon pointed tail self-tapping 1/2-13 1/4-20 3/4

We have more than ten years of production experience in the screw industry. The main products are: blue and white zinc rivets, flat washer combination screws, high-footed and wide-brimmed eyelets, processed bolts, iron plate nuts, extended belt screws, widened flat washers ,Complete specifications of screws, national standard galvanized, lengthened and super-long pull-out screws, can be equipped with nut washers, rivet nuts, flat-head knurled screws, hot promotions, blue nylon rings and other fasteners, due to the different materials and specifications of the products Different, the price is also different, if you need, please contact us.

Online consultationMobile hotline
132 6870 6820
Product introduction

Screw Specifications

Screw head table

A nut provided by Yueluo. The nut is in the shape of a sleeve and has a threaded section inside. An annular groove is set on the inner wall of one end of the threaded section. The notch of the groove points to the hole core. The hole diameter at the groove notch at the front end is larger than the nominal size of the thread segment or the hole diameter at the groove notch at the rear end in the screwing direction is smaller than the nominal size of the thread segment.

Processing cup head hexagon socket self-tapping screws

rotating rod is rotatably installed on one side of the two pillars that are close to each other, and a second bevel gear is welded on the ends of the two rotating rods that are close to each other. The two second bevel gears are meshed with the two first bevel gears respectively. , The first sprocket is welded on the two rotating rods, the chain is meshed on the two first sprockets, and the screw rods are installed on the sides of the two pillars that are close to each other. Above the rod, the second sprockets are welded on the two screw rods, the two second sprockets are connected to the two first sprockets through two chains respectively, and threaded blocks are threaded on the two screw rods. The sides of the two threaded blocks close to each other are symmetrically welded with connecting columns, and the sides of the four connecting columns close to each other are welded with movable rods respectively. The other ends of the support plates are respectively rotatably installed with the same support plate, and the assembly device body is fixedly installed on the top of the support plate.

Self-tapping nickel-plated cylindrical head with inner hexagon pointed tail


The existing spring pads are generally composed of longitudinal support springs, transverse connection springs, support springs, frames and frame clips. (Commonly known as string spring) is a slender and constant warp spring, used to connect the longitudinal support spring. The support spring is located at the edge of the spring pad to increase the shear resistance of the spring pad and the support strength of the frame. The surrounding frame connects the spring to the spring. up, fixed. The existing treatment method is to first heat-process the longitudinal support spring and the support spring made of 70# steel wire through the winding spring in a chemical solution, arrange them, and fix and connect them with a string spring, a frame and a clamping piece. Because the string spring and the frame have not been chemically heat treated, there is a large internal stress. Therefore, this treatment method has two disadvantages. One is that the processing efficiency of the heat treatment support spring is low. Larger, the spring is easily deformed and the service life is affected. In addition, the chemical solution after heat treatment is easy to cause environmental pollution


Nuts are parts that tightly connect mechanical equipment. Through the inner thread, nuts and bolts of the same specification can be connected together. At present, most nuts are used together with gaskets when they are locked, or are set as an integrated structure, which has the advantage of increasing Friction, strengthen the effect of tightening, but the square nut is usually used directly without adding a gasket, and the upper and lower end faces are flat, very smooth, when subjected to strong vibration, it is very easy to loosen, and the tightening effect is not good.


The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].

Cooperation Case

Hot Recommend