Customized 304 stainless steel extended pull-explosion expansion bolt explosion screw 3/4 1/4-20

We have more than ten years of production experience in the screw industry, the main products are: wheel hub cap nuts, furniture nuts, rivet nuts, zinc outer diameter 5.4 negative SOO, screws and bolts, hex nuts, nuts, screws, countersunk head internal and external teeth half hexagon Rivet Nuts, Mechanical Instrument Screws, Flat Head Bare Body Blind Hole Rivet Nuts, Carbon Steel T-Head Bolts, Galvanized Countersunk Nuts, Set of Four Corner Nuts, Single-Headed Teeth Reduction Rod Copper Posts, Metal Small Washers Thickened Thin Gaskets, Speakers Fasteners such as nuts and bolts have different prices due to different product materials and specifications. Please contact us if you need them.

Online consultationMobile hotline
132 6870 6820
Product introduction

Screw Specifications

Screw head table

Stainless Steel Nut Nut Self-locking Nut, Lock Nut, Lock Nut, Four-jaw Nut, Screw-in Nut Safety Nut, Thin Rod Screw Connection Nut, Self-locking Hexagonal Cap Nut, Special Ground Screw Nut, Hexagonal Crown Thin Nut , Lifting ring nut. [1] Fine pitch all-metal hexagonal flange face locking nut, all-metal hexagonal flange face locking nut, fine pitch non-metallic insert hexagonal flange face locking nut, fine pitch hexagonal flange face nut welding square nut, Welded Hex Nuts, Snap Nuts, Insert Round Nuts

Customized 304 stainless steel

1. When the main body is large equipment, accessories need to be installed, such as sight glass, mechanical seal seat, deceleration frame, etc. At this time, a stud bolt is used, one end is screwed into the main body, and the other end is equipped with a nut after the accessory is installed. Since the accessory is often disassembled, the thread will be worn or damaged, and it is very convenient to use the stud bolt to replace. 2. When the thickness of the connecting body is very large and the bolt length is very long, stud bolts will be used. 3. It is used to connect thick plates and places where it is inconvenient to use hexagonal bolts, such as concrete roof trusses, roof beam suspension monorail beam suspension parts, etc.

Lengthened tension and explosion expansion bolts

exploding screw

The main purpose is to make industrial products form a fixed one. In use, it often occurs that the teeth cannot be closely attached, and the screw heads are broken if they are locked too hard, or the teeth are not locked tightly and fail to meet the conditions of use, all of which are accuracy problems. . Screws are mass products, not hand-made works of art. In mass production, they are supplied to consumers in order to achieve high precision, stable quality and popular prices. The accuracy of screws is usually 6g (class 2, the American standard IFI is 2A teeth), and the rough screws used in construction projects are 8g (class 3, IFI is 1A teeth). Common types of screws Screw A: Machine Screw: Machine screw B: Tapping Screw: Self-tapping screw (for metal and plastic) B-1: Sheet Metal Tapping Screw. (Iron die self-tapping screw) B- 2: Plastic Tapping Screw. (for plastic, self-tapping screw) C: Wooden Screw : Woodworking screw D: Drywall Screw : Cement wall screw E: Self Drilling Screws (stainless steel drilling screw, composite material drilling screw) F : Expansion screw, four-piece expansion screw, also known as: four-piece gecko. The grades of expansion bolts are divided into: 45, 50, 60, 70, 80. Materials of expansion screws: mainly austenitic A1, A2, A4, 1 stainless steel plate, metal steel plate, galvanized steel plate, engineering installation. 2. Indoor and outdoor installation of metal curtain wall and metal light compartment. 3 Generally, angle steel, channel steel, iron plate and other metal materials are combined for installation. 4. Assembly engineering of car boxes, container boxes, shipbuilding, refrigeration, screw machine equipment, etc. Features: 1. Drilling and tapping, locking is completed at one time, and the bonding force is strong. 2. Save construction time and improve work efficiency. E-1:STAINLESS STEEL SELF DRILLING SCREWS E-2:Bi-Metal Self Drilling Screws Common materials of composite drilling screws a.Low Carbon Steel: carbon steel carbon steel is divided into low carbon steel, medium carbon steel, high Carbon steel and alloy steel. b. SS-304: Stainless Steel 304 and 316 belong to stainless steel c. SS-302: Stainless Steel 302: better structural toughness d. Aluminum 5052: Aluminum alloy 5052 d. Brass: Brass e. Bronze: Bronze f . UNS C11000 Copper: Antimony Copper

3/4

The classification of the second combination screw is divided according to the material of the screw wire and the hardness index of the screw wire. Generally, the two combination screws are divided into stainless steel and iron, and stainless steel is divided into stainless steel 201, stainless steel 304 and stainless steel 316. Iron is divided into three types: low carbon steel, medium carbon steel, and high carbon steel. Carbon steel combination screws refer to iron combination screws. Generally, iron combination screws are classified into grades 4.8, 8.8, 10.9, and 12.9. But in the market, the combination screws of grade 10.9 and grade 12.9 are rarely used, so we won't talk about it here. And the two combination screws on the market are more commonly used combination screws of grade 4.8 and 8.8. 4.8 grade combination screws are generally made of 1010A screw wire rods. After the screw wire rods are beaten into screws, they are combined with spring flat washers. After production, this 4.8 grade combination screw does not need to be hardened. Its hardness can reach 4.8. The 8.8 grade combination screw is generally made of 10B21 screw wire. After the screw wire is punched into a screw, it is equipped with a spring washer and a flat washer, and the three pieces can be combined and rubbed by an automatic spring-flat washer machine. Fasten the spring-flat washer combination on the screw, and the spring-flat washer will not fall off. After the combination screw is produced, it needs to be hardened to make the hardness reach 8.8. After the hardness reaches 8.8, we need to take it for electroplating. In order to prevent hydrogen embrittlement of the spring washer in the 8.8-level combination screw with added hardness, it is easy to break. In this way, it is necessary to carry out hydrogen removal treatment on the hardened combined screws, and the electroplating can only be done after the hydrogen removal.

1/4-20

The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].

Cooperation Case

Hot Recommend