What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Anchor bolts are also known as stiffened anchor plate anchor bolts, welded anchor bolts, anchor claw anchor bolts, rib plate anchor bolts, anchor bolts, anchor screws, anchor wires, etc. It is specially designed to be buried in the concrete foundation and used as the base for fixing various machines and equipment. Figure 7 anchor bolts are the most commonly used anchor bolts. It is generally made of Q235 steel, with high strength using Q345B or 16Mn material, and also using 40Cr material to process 8.8-strength products, and occasionally using secondary or tertiary rebar. Anchor bolts are divided into wool, thick rod and thin rod. The wool material is the raw material steel, which is directly processed from round steel or wire without modification; thick rods or called A-type, thin rods or B-type, are processed from steel modified into the corresponding required rod diameter. Welded anchor bolts are made of single-headed bolts welded with stiffened iron plates. Its anti-pulling ability is strong. According to the different conditions of use, it can reach 3.6, 4.8, 6.8, 8.8 and other grades respectively. The tensile capacity of 3.6 grade 7-shaped anchor bolts is the tensile capacity of the steel itself. The tensile strength of anchor bolts directly processed from Q345B or 16Mn raw materials can reach a tensile strength of 5.8. The tensile strength of grades 4.8, 5.8, 6.8 and 8.8 refer to the provisions on mechanical properties in GB/T3098.1.
leak-proof combined gasket relates to a gasket and solves the problem of short service life of the existing gasket. The combined gasket comprises: an O-shaped sealing ring, which is an annular sealing ring with an outer diameter of D and an inner diameter of E. The section diameter is A; the steel outer ring is a steel flat annular outer ring, which is sleeved on the outer surface of the O-ring, the inner diameter is F, and F=D, the thickness is B, B=0.785A ;The steel inner ring is a steel flat annular inner ring, embedded in the inner surface of the O-ring, the outer diameter is G, and G=E; the thickness is C, and C=B. When the O-ring in the combined washer is pressed by the bolt for sealing, it is positioned between the steel outer ring and the steel inner ring, and is protected by both of them, so that the tightening torque of the bolt can be reduced at least Double the sealing performance without reducing the sealing performance, extending the service life of the thread and reducing the production cost.
In general, the size, mechanical properties and working performance requirements of self-tapping screws have the following standards: 1. Self-tapping screw size standard ASME B18.6.3 2010 standard not only introduces the dimensions of slotted and cross-recessed self-tapping screws and metal drive screws, but also includes the mechanical properties and work performance requirements of carbon steel self-tapping screws. The appendix gives instructions for measuring the various dimensions and application guidance on clamping lengths and test apertures. 2. Self-tapping screw performance standards (including mechanical properties and work performance): (1) SAE J933: Introduces the mechanical performance and work performance requirements of carbon steel ordinary self-tapping screws and white-cut self-tapping screws. The requirements for selection of raw materials, heat treatment, depth of carburized layer, surface hardness, and core hardness are further specified. (2) SAE J81: The mechanical properties and working performance of self-extrusion self-tapping screws (self-tapping locking screws) are introduced. (3) SAE J78: The mechanical properties and working properties of self-drilling and self-tapping screws are introduced. (4) IFl-113: The mechanical properties and working properties of self-drilling and self-tapping screws are introduced. (5) ASTM C1513: Introduces the mechanical properties and performance requirements of carbon steel self-tapping screws. For other special types of self-tapping screws, there is no corresponding national or industrial standard, and no data for self-tapping screws made of other metal materials other than carbon steel have been recognized. For technical data on these self-tapping screws, you can check with the manufacturer.
With the development of science and technology, the advancement of technology, the rapid change of automotive products, also put forward higher requirements for fastener products, and automotive fastener-related products, especially in the process of assembling auto parts, in order to effectively improve the bolts The fastening strength is mostly made of combined gaskets (flat gaskets, cone gaskets) and riveted nuts to meet the assembly requirements.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
