What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
shaft retaining ring installation tool and an installation method thereof relate to an assembly tool and an installation method thereof, comprising a pressing cylinder and a taper sleeve. The maximum diameter of the tapered end is slightly smaller than the inner diameter of the circular straight hole of the pressing cylinder, and the lower end of the tapered sleeve has a positioning structure matched with the shaft of the shaft retaining ring to be installed. The method includes the following: place the taper sleeve on one end of the shaft where the shaft retaining ring is to be installed and position it well, then place the shaft retaining ring on the tapered end of the taper sleeve, and finally press down the pressure cylinder to make the shaft Use the retaining ring to slide down the conical surface of the taper sleeve to the shaft to be installed with the retaining ring for the shaft, and finally get stuck in the groove of the shaft. Yueluo does not need to open the retaining ring for the shaft, which reduces the operation force and labor intensity. The operation method is simple, the structure is simple and reliable, the cost is low, and it is easy to popularize and use.
The process of removing iron oxide plate from cold heading steel wire rod is stripping and dephosphorization. There are two methods: mechanical dephosphorization and chemical pickling. Replacing the chemical pickling process of wire rod with mechanical phosphorus removal not only improves productivity, but also reduces environmental pollution. This phosphorus removal process includes bending method (the round wheel with triangular grooves is commonly used to repeatedly bend the wire rod), spray nine method, etc. The phosphorus removal effect is good, but the residual iron and phosphorus cannot be removed (the removal rate of iron oxide scale is 97%) ), especially when the iron oxide scale is very sticky, therefore, mechanical phosphorus removal is affected by iron scale thickness, structure and stress state. Carbon steel wire rods used for low strength fasteners (less than or equal to 6.8) High-strength bolts (greater than or equal to grade 8.8) use wire rods to remove all iron oxide scales after mechanical dephosphorization, and then go through a chemical pickling process for compound dephosphorization. For low carbon steel wire rods, the iron sheets left by mechanical dephosphorization are likely to cause uneven wear of grain draft. When the grain draft hole adheres to the iron sheet when the wire rod rubs against the external temperature, the surface of the wire rod produces longitudinal grain marks. More than 95% are caused by scratches on the surface of the steel wire during the drawing process. Therefore, the mechanical phosphorus removal method is not suitable for high-speed drawing.
The tooling for screw standard parts provided by Yueluo Guangdong Yueluo Hardware Industry Co., Ltd. mainly solves the problems of low manual operation matching efficiency, wrong specifications of screw standard parts, and easy falling of screw standard parts into the product when assembling screws in the prior art. . The specific technical solutions of Guangdong Yueluo Hardware Industry Co., Ltd. are as follows. The screw standard parts supporting tooling includes a stud sleeve hole plate, a gasket sleeve hole plate and a nut sleeve hole plate with matching structure; the stud sleeve hole plate There is at least one stud hole matching with the assembled stud structure, at least one gasket hole matching with the assembled gasket structure is arranged on the gasket sleeve hole plate, and the nut sleeve hole plate is provided with at least one gasket hole matching with the assembled gasket structure. At least one nut hole matched with the assembled nut structure; the number of stud holes, gasket holes and nut holes are equal. The above-mentioned stud sleeve hole plate is provided with a positioning device, and the gasket sleeve hole plate is provided with a matching positioning hole; or the gasket sleeve hole plate is provided with a positioning device, and the stud sleeve hole plate is provided with a matching positioning hole. The above stud holes are through holes; the nut holes are blind holes. Forty to one hundred and fifty stud holes are arranged on the stud sleeve hole plate. The above-mentioned positioning device is a positioning plate and/or a positioning column. The advantage of Guangdong Yueluo Hardware Industry Co., Ltd. is that the matching tooling for screw standard parts improves the matching quality of screw standard parts, effectively prevents screw standard parts from falling into the product easily and screw specifications are wrong; it simplifies the matching difficulty of screw standard parts and improves assembly efficiency. . The screw standard parts supporting tooling can be processed differently according to different screw standard parts specifications, and the applicability is very wide.
hand screw is a screw with a plastic head, and the user fixes the hand screw by turning the plastic head by hand. At present, a hand screw is disclosed in the market publication number CN202203253U, which includes a plastic head and a screw rod, the plastic head and the screw rod are connected together, and the height of the plastic head is higher than that of an ordinary screw, and the height is 12 cm. The screw of the hand screw is fixed in the plastic head by glue. After a period of use, the aging of the glue leads to the loosening of the screw and the plastic head. When the plastic head is stressed, the screw rod comes out of the plastic head, which affects the normal use of the hand screw.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
