Machining 304 Stainless Steel DIN916K Hexagon Socket Knurled Set Screws 5/8

pin fixing device, comprising fastening bolts for processing and fixing two workpieces, wherein the pin fixing device further comprises a fixing groove arranged on the workpiece, a positioning hole which is arranged on the workpiece and communicated with the fixing groove, and a positioning hole is arranged in the positioning hole A pin is provided with a pin bushing, the pin bushing is sleeved on the positioning pin, an accommodation space is provided between the pin bushing and the inner wall of the fixing groove, and colloid is filled in the accommodation space. The use of the pin fixing device of Guangdong Yueluo Hardware Industry Co., Ltd. can greatly improve the positioning accuracy of the pin, improve the processing efficiency, reduce the manufacturing cost, testing cost and labor cost, with strong mobility and quick response.

1. First remove the sludge on the surface of the broken head of the broken screw, use the center gun to kill the center gun of the section, and then use an electric drill to install a drill bit with a diameter of 6-8 mm to drill the hole in the center of the section, pay attention to the hole must be drilled through. After the hole is drilled through, remove the small drill bit and replace it with a drill bit with a diameter of 16 mm, and continue to expand and drill through the hole of the broken bolt. 2. Take a welding rod with a diameter of less than 3.2 mm and use a medium and small current to carry out surfacing welding from the inside to the outside in the hole of the broken bolt. Take half of the entire length of the broken bolt at the beginning of the surfacing welding. When starting the surfacing welding, the arc should not be too long. In order to avoid burning through the outer wall of the broken bolt, surfacing to the upper end face of the broken bolt, and then continue surfacing to weld a cylinder with a diameter of 14-16 mm and a height of 8-10 mm. 3. After the surfacing is completed, hammer the end face with a hammer to make the broken bolt vibrate along its axial direction. Due to the heat generated by the previous arc and the subsequent cooling plus the vibration at this time, the broken bolt and the thread of the body will be loose in between. 4. Carefully observe, when it is found that a small amount of rust leaks from the fracture after the knock, take the M18 nut and put it on the surfacing column head and weld the two together. 5. After welding, use a torx wrench to cover the nut while it is still hot, and twist it back and forth, or tap the end face of the nut with a small hand hammer while twisting back and forth, so that the broken bolt can be taken out. 6. After taking out the broken bolt, use a suitable tap to process the thread in the frame to remove rust and other debris in the hole.

Generally known bolts refer to screws with a larger diameter. According to this statement, the diameter of screws is much smaller than that of bolts. Stud bolts do not have a head, and some are called studs. Both ends of the stud are threaded, with no thread in the middle and a smooth rod in the middle. Studs are used on large equipment such as gear racks. In actual use, the external load will have vibration and the influence of temperature will reduce the frictional force, and the threaded connection will loosen and fail over time. Therefore, it is necessary to do a good job in the maintenance of the stud bolts at ordinary times. Stud bolts or anchor bolts will have problems under the action of mechanical friction for a long time. When problems occur, the engine oil pan should be removed, and the use of the engine bearing bushes should be carefully checked, and the clearance between the bearing bushes should be checked. Whether it is too large, if the gap is too large, it should be replaced in time. When replacing the stud bolts, also replace the connecting rod bolts. When some large equipment such as nail making machines are in normal operation, if they find that the engine is not running very stable or there is abnormal noise, they should stop and check in time to avoid bigger problems.

5. After the closing value material and the geometric parameters of the nut are determined, the change of the closing value has an important influence on the repeated use characteristics of the lock nut. When the closing value becomes larger, the deformation of the threaded piece increases, the strain of the threaded piece increases, the strain cycle hardening phenomenon intensifies, and the pressure FN of the threaded piece increases, which has a tendency to increase the unscrewing torque; on the other hand, the width of the threaded piece decreases. , the total area of the threaded piece decreases, the friction with the bolt decreases, the strain of the threaded piece increases, the low-cycle fatigue performance decreases, and the maximum unscrewing torque tends to decrease. Under the combined action of various factors, the change of the maximum unscrewing torque with the number of repeated uses is difficult to predict, and it can only be observed through experiments.

The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].