your location: 首页>>Yueluo products>>Nut size

Customized metal self-locking nut flange surface steel sheet locking nut auto parts nut nut

We have more than ten years of production experience in the screw industry, the main products are: solid aluminum rivets, FHS pressure riveting screws and screws, anti-fall anti-loosening screws and bolts, pressure riveting parts nut columns, left-handed left-hand thread nuts, fine thread nuts and fine thread nuts, 16582 open round head rivets, bolt and screw sets, double lug stop washers, GB97 blackened 8-level flat washers, coupling long nuts, large flat head socket head cap bolts, welding terminals, ingot screws, flat head bolts, etc. Due to the different materials and specifications of the products, the prices are also different, if necessary, please contact us.

Online consultationMobile hotline
132 6870 6820
Product introduction

Screw Specifications

Screw head table

The process factors that affect the quality of high-strength fasteners include steel design, spheroidizing annealing, peeling and dephosphorization, drawing, cold heading, thread processing, heat treatment, etc., and sometimes the superposition of various factors.

Customized metal self-locking nuts

Generally, the bolts or nuts used to press workpieces or fixtures in the T-slot of the machine tool table are made into square or rectangle. Things are very inconvenient.

Flange steel sheet

fasten the screw nut

Guangdong Yueluo Hardware Industry Co., Ltd. provides a kind of rivet, parts and parts are riveted by the rivet, the part has a fixed plate and a fixed plate, and the part is located between the fixed plate and the fixed plate, The rivet includes a nail head, a nail post and a nail post which are connected in sequence, the diameter of the nail post is larger than the diameter of the nail post, the nail head is matched with the outer end surface of the fixing plate, and the length of the nail post is It is greater than the sum of the riveting length of the fixing plate and the riveting length of the part. The rivet can control the distance between the parts, so that the relative rotation of the two parts is more smooth and easy to operate.

auto parts

Procurement and sales in the testing process know that the quality of screws is manufactured, not detected, but in manufacturing, we must try our best to make them as good as possible. But it is unlikely to be completely error-free and error-free. We all know that errors are unavoidable and can only be approached infinitely. Therefore, at this time, the quality inspection of the screw is required to improve the quality of the screw. At the beginning of ordering from screw wire material into the production of screw industry manufacturers, you must first check the wire diameter of the screw wire and the material of the screw. Generally, the wire diameter of the screw is measured with a caliper to measure the size of the wire diameter, whether it is suitable for self-ordering. Same size. After testing these, it is the testing in the production process, starting from the head of the screw, to determine the size of the head, the opposite side of the head, the diagonal angle, the depth of the cross groove, the tolerance range of the screw, and so on. These are checked with calipers. In the inspection of all aspects when rolling teeth, the main thing is whether the thread can pass the pass and stop gauge, and whether the screw thread can pass the gauge and stop. Next is the electroplating measurement problem. After electroplating, whether it meets the requirements of environmental protection and whether it can pass the time required by the salt spray. Tools include environmental testing machines and salt spray testing machines. In short, in the process of screw production and sales, there must be necessary tools to detect the quality of screws. The summary should be summarized as follows: calipers, hardness testers, salt spray machines, environmental testing machines, pass and stop gauges, etc. When producing and selling screws, there will be a screw specification and screw model. With the screw specification and screw model, we can understand what specification screw and what size screw the customer needs. Many screw specifications and screw models are based on national standard specifications and models. Generally, such screws are called ordinary screws, which are generally available on the market. There are some non-standard screws, which are not based on the national standard specifications, models and sizes, but are customized according to the standards required by the product materials. There is no stock in the general market at all. In this way, it is necessary to make drawings and samples.

Nut Nut

The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].

Cooperation Case

Hot Recommend