What is the tolerance range of precision screws?
What is the tolerance range of precision screws?
Alloy Steel Nuts Hexagon Nuts (GB6170/DIN934, GB6175), Flange Nuts (GB6177/DIN6923) Round Nuts (GB812), Small Round Nuts (GB810), American Square Nuts, American Hex Nuts (ANSI/ASME B18.2.2) , Heavy-duty nuts (metric, US). Size: 5/16-4.
Fasteners are a type of mechanical parts that are used for fastening connections and are widely used. Fasteners are used in a wide range of industries, including energy, electronics, electrical appliances, machinery, chemicals, metallurgy, molds, hydraulics, etc., in various machinery, equipment, vehicles, ships, railways, bridges, buildings, structures, tools, instruments, etc. , chemical industry, instruments and supplies, etc., you can see all kinds of fasteners, which are the most widely used mechanical basic parts. It is characterized by a wide variety of specifications, different performance uses, and a very high degree of standardization, serialization and generalization. Therefore, some people also refer to a type of fasteners that have been standardized as standard fasteners, or simply referred to as standard parts.
At present, the industry uses the pure manual installation method to install the elastic cylindrical pin, that is, the staff first holds the tool holder; then, manually puts the elastic cylindrical pin into the elastic cylindrical pin hole of the tool holder; then, use the body to align the tool holder For positioning, use a hammer to knock the elastic cylindrical pin into the tool holder. This installation method requires manual operation throughout the entire process, and the work efficiency is low. Moreover, when the hammer is knocked, the staff needs to use the body to position the tool holder, there is a risk of smashing and injuring people, and there is a potential safety hazard. In addition, hammering will cause deformation of the elastic cylindrical pin, and the qualification rate of assembly is low.
Gaskets are widely used in the machinery industry. According to the different needs of machinery and equipment in different industries, the structural forms of the sealing points are also different. Plum washer is one of the commonly used seals. It is commonly used between the pump and the motor coupling. In the actual production process of the enterprise, it is found that due to the influence of the material and structure, this type of gasket in common use can withstand impact force. Small, the septum is easily damaged. Because the current plum washers are all one-piece structures, even if one or several of the partitions are damaged, they need to be replaced as a whole. Although the value of a single plum washer is low, it needs to be shut down for maintenance and replacement almost every week. It also seriously affects the normal production of the enterprise, and the one-piece plum blossom gasket is also difficult to repair, adding unnecessary use costs to the enterprise. For this reason, the plum blossom gasket needs to be improved to strengthen the impact resistance of the gasket, and can be repeated Maintenance and use, prolong the maintenance cycle of the equipment, and ensure the normal production of the enterprise. The purpose of the utility model Yueluo is to solve the above-mentioned deficiencies in the existing technology, improve the existing technology, and provide a simple structure, which strengthens the impact resistance of the gasket, and can be repeatedly maintained and used to prolong the maintenance of the equipment. The cycle guarantees the plum blossom elastic washer normally produced by the enterprise. In order to achieve the above purpose, Yueluo is achieved through the following technical solutions-namely a plum blossom elastic washer, including an elastic washer body with a partition, the technical point is that the washer body is composed of a washer base and a partition that is independent of each other. , the septum and the gasket base are fixedly connected into one through the fixing piece. In order to further strengthen the impact resistance of Yueluo, the contact parts of the spacer and the washer base are respectively processed with a limited clamping table and a matching groove, so that the spacer and the washer base can be better integrated into one. According to the different specifications of the torx washer, the spacer and the washer can be fixed as a whole by rivets; or by screws. In addition, a semi-rigid tightening ring with grooves is embedded inside the washer base, and the width of the tightening ring is smaller than the width of the washer base; the ends of the rivets or screws are located in the grooves of the tightening ring, so as not to affect the performance of the torx washer JH is often installed. After the above improvement, Yueluo has improved the one-piece structure of the plum-blossom washer into a split structure and adopted a variety of fixed structure forms, so it has a simple structure, strengthens the impact resistance of the gasket, and can be repeatedly maintained and used. , Extend the maintenance cycle of the equipment and ensure the advantages of the normal production of the enterprise.
The above content is uploaded by Yueluo or the Internet. If there is any copyright issue, please contact [email protected].
